Showing posts with label cylinder. Show all posts
Showing posts with label cylinder. Show all posts

Tuesday, February 18, 2014

How Do I Replace the Slave Cylinder for a 1990 Ford Ranger 2 3L

How Do I Replace the Slave Cylinder for a 1990 Ford Ranger 2.3L?

The 1990 Ford Ranger 2.3-liter pickup uses a concentric slave cylinder, which is located inside the transmission. This means that the transmission must be removed to replace the slave cylinder. When you remove the transmission, if the clutch is older, it is a good idea to replace it at the same time, simply because of the time required to complete the job. You will need a special clutch coupling removal tool, part number T88T-70522-A, which is available at any Ford dealership.

Instructions

    1

    Disconnect the battery ground cable and lay it aside, making sure that it does not touch metal. Use the clutch coupling removal tool to disconnect the coupling at the transmission. Slide the white, plastic sleeve towards the slave cylinder with one hand and tug on the tube with the other.

    2

    Remove the lever, shim and bushing from the transmission with the appropriate sockets. Stuff a rag into the opening to keep dirt and debris from falling into the transmission. Disconnect the clutch master cylinder push rod from the clutch pedal with the appropriate socket.

    3

    Jack up the Ranger with a floor jack and support it on jack stands. Make a mark on the drive shaft and at the same place on the rear axle flange so you know how to line up the drive shaft when you put it back in. Remove the drive shaft at the axle with the appropriate socket then pull it out of the rear of the transmission. Plug the housing to prevent fluid from leaking out.

    4

    Unbolt and remove the dust shield from the clutch housing with the appropriate socket. Remove the wires from the starter and lay them aside. Remove the harness for the back-up light (near the starter). Unbolt and remove the starter with the appropriate socket. Unscrew the speedometer cable from the transmission and set it out of the way.

    5

    Place a block of wood on one of the floor jacks. Slide it under the engine oil pan and jack it up so that the wood just touches the bottom of the oil pan to support the engine. Place a second jack under the transmission. If you are using a lift, use a transmission jack instead.

    6

    Remove the bell housing bolts and washers with the appropriate socket. Remove the transmission mounting bolts and the damper retaining bolts and nuts with the appropriate socket. Unbolt and remove the cross-member.

    7

    Lower the transmission jack and, at the same time, work the transmission off its dowel pins. Pull the transmission towards the back of the Ranger then place it on the ground. If you are using a floor jack, you can leave it on the floor jack if it is stable on the jack.

    8

    Remove the clutch housing-to-transmission nuts then pull the housing assembly off the transmission. Remove the slave cylinder from the input shaft. Slide the new slave cylinder over the input shaft, making sure the tower part of the slave cylinder faces the transmission.

    9

    Reinstall the clutch housing. The clutch housing has notches that line up with the slave cylinder. Make sure the slave cylinder is located properly in the clutch housing notches. Clean the mating surface of the clutch housing and the rear of the engine, especially around the dowel holes, with rags and carburetor cleaner. If there are burrs that will not wipe off easily, gently go over them with fine-grit sandpaper. Clean the area with carburetor cleaner and rags after sanding.

    10

    Raise the transmission with the jack. Line up the input shaft splines with the clutch disc splines. Move the transmission in towards the dowels, adjusting the jack as needed. Push the transmission onto the dowels.

    11

    Install the bell housing bolts and washers. Put the washers in place so that the bolts do not damage the aluminum bell housing. Tighten the bolts to 33 foot-pounds of torque. Move the transmission jack out of the way.

    12

    Reinstall the starter and tighten the bolts to 17 foot-pounds of torque. Jack the engine up with the floor jack. Reinstall the cross-member, transmission mount and damper. Tighten the bolts firmly. Remove the floor jack from under the engine. Reinstall the drive shaft by pushing it into the transmission extension housing then connecting it to the rear axle flange. Make sure the marks you made earlier line up. Reattach the washer, lock washer and the nuts. Tighten the drive shaft-to-flange nuts to 70 foot-pounds of torque.

    13

    Reinstall the dust shield. Tighten the dust shield bolts to 8 foot-pounds of torque. Reinstall the starter, the starter wires, the back-up lamp wiring harness and the speedometer cable. Check the transmission fluid level. Add Ford manual transmission lube as needed.

    14

    Remove the rags from the shifter hole. Reinstall the gearshift lever, shim and bushing with the appropriate sockets. Reinstall the lever-to-cover bolts and the boot retaining screws. Reconnect the master cylinder push rod to the clutch pedal with the appropriate socket. Attach the battery ground cable to the battery ground terminal. Bleed the clutch.

Read here..

Sunday, December 8, 2013

How to Remove Replace a Cylinder Head on a 6 9 Ford

The 6.9-liter engine that appears in Ford trucks from 1982 to 1994 has eight cylinders and uses indirect fuel injection. This engine is most common in larger trucks, beginning with the 1/2 ton F250 pickups. The cylinder head in a 6.9-liter Ford engine is a platform that sits on on top of the cylinder block. The procedure for replacing the cylinder head is generally the same for all vehicles with a 6.9-liter Ford engine.

Instructions

    1

    Disconnect the cables from the negative terminals of both batteries with a socket wrench. Drain the coolant from the radiator into a clean container, and store it for later use. Disconnect the shrouds from the radiator fan. Remove the radiator fan assembly with special tools T83T-6312-A and T83T-6312-B. Turn the mounting nut for the radiator fan clutch clockwise to loosen it.

    2

    Remove the electrical wiring from the alternator. Disconnect the mounting bolts for the alternator and the vacuum pump with a socket wrench. Remove the alternator and vacuum pump from the vehicle. Detach the hose for the heater from the cylinder head. Disconnect the fuel injection pump from the cover of the intake manifold with a socket wrench, and detach the intake manifold cover.

    3

    Raise the truck with a floor jack, and support it on jack stands. Remove the exhaust pipes from the exhaust manifolds. Release the clamp on the oil dipstick tube. Disconnect the mounting bolts that attach the oil dipstick tube to the cylinder head, and remove the oil dipstick tube from the vehicle. Lower the truck with the floor jack.

    4

    Disconnect the valve cover with a socket wrench. Remove the rocker arms and pushrods from the cylinder head. Record the position of each push rod and rocker arm as you remove them to ensure you install them to their original position. Remove the fuel injector nozzles and glow plugs from the engine.

    5

    Disconnect the mounting bolts for the cylinder head with a socket wrench. Attach lifting eyes to each end of the cylinder head with special tool T70P-6000. Lift the cylinder head with the lifting eyes, and remove it from the engine compartment.

    6

    Place the new cylinder head onto the engine block, while ensuring the pre-chambers dont fall into the cylinder bores. Coat the mounting bolts for the cylinder head with engine oil. Fasten the mounting bolts for the cylinder head, and tighten them in four separate passes with a socket wrench.

    7

    Coat the ends of the push rods with engine oil. Install the push rods in the positions you recorded in step four, and ensure the push rods are properly seated. Lubricate the tips of the valve stems with Lubriplate grease. Turn the crankshaft by hand to move its timing mark to the 11 oclock position. Install the rocker arms to their original, and tighten their mounting bolts to 27 foot-pounds with a torque wrench.

    8

    Replace the valve covers with a socket wrench. Install the intake manifold, and connect the fuel injection pump to the intake manifold. Attach the hose from the heater to the cylinder head. Install the alternator and vacuum pump to the engine, and connect the oil dip stick. Install the exhaust pipe to the exhaust manifolds, and attach the electrical wiring for the alternator. Connect the air cleaner to the engine.

    9

    Install the radiator clutch assembly with special tools T83T-6312A and T83T-6312B. Attach the cables to the negative battery terminals with a socket wrench. Fill the radiator with coolant, and start the engine. Check for leaks in the exhaust, coolant and fuel systems.

Read here..

Tuesday, November 12, 2013

How to Replace a 1997 Buick 3 1L 6 Cylinder Timing Chain

The timing chain on a 3.1L Buick engine turns the crankshaft in synchronization to the camshaft rotation. This engine is known for its reliability, but after tens of thousands of miles the timing chain can simply stretch and fail. This can seriously damage the engine and affect performance. Plan accordingly, as the timing chain replacement procedure can require a good part of a day.

Instructions

    1

    Remove the engine front cover. Rotate the crankshaft until the timing marks are aligned with the crankshaft sprocket, camshaft sprocket locator hole and the engine block. The number one cylinder should be at top dead center (TDC).

    2

    Unscrew the camshaft sprocket bolt. Remove the camshaft sprocket and the timing chain. Remove the timing chain. Use a crankshaft sprocket remover to remove the crankshaft sprocket. Remove the timing chain dampener bolts. Remove the timing chain dampener.

    3

    Replace the timing chain. Install the crankshaft sprocket using a crankshaft sprocket installer. Apply GM EOS P/N 1052367 or equivalent to the sprocket thrust surface. Install the timing chain dampener to the block. Tighten the timing chain dampener bolts to 15 foot-pounds.

    4

    Align the crankshaft timing mark to the timing mark on the bottom of the chain dampener. Hold the camshaft sprocket with the chain hanging down and install the chain to the crankshaft gear. Align the timing mark on the camshaft gear (center line of the locator hole) with the timing mark on the top of the chain damper.

    5

    Remove the Crankshaft Sprocket Installer. Align the dowel in the camshaft with the dowel hole in the camshaft sprocket. Draw the camshaft sprocket onto the camshaft using the mounting bolt. Coat the crankshaft and camshaft sprocket with engine oil. Install the camshaft sprocket bolt. Tighten the bolt to 81 foot-pounds. Install the engine front cover.

Read here..

Tuesday, October 22, 2013

How to Replace a Clutch Master Cylinder on a 1991 Accord

When the clutch pedal on your Honda Accord becomes soft, theres a good chance you are experiencing a faulty clutch master cylinder. If left unchecked at this point, it is only a matter of time before the master cylinder completely fails and you will be unable to shift your car. If you have a couple of hours and minimal tools, you can replace the clutch master cylinder at home.

Instructions

    1

    Disconnect the cable from the negative terminal on your cars battery. This is an essential first step in any car repair due to the risk of electrical shock.

    2

    Pull the cotter pin located about halfway up the clutch pedal assembly. While you are under the dashboard, you also need to remove the pedal pin from the yoke.

    3

    Locate the master cylinder on the engine compartment side of the firewall. Turn the bolts counterclockwise to remove them from the firewall so you can remove the faulty master cylinder.

    4

    Remove the hydraulic lines from the master cylinder. Make sure you have rags on your work surface so you minimize the mess from leaking clutch fluid.

    5

    Place the hydraulic lines on the new master cylinder and install the master cylinder onto the firewall. Turn the bolts clockwise to properly tighten them.

    6

    Insert the pedal pin into the yoke and the cotter pin into the clutch pedal assembly.

    7

    Fill the fluid reservoir with clutch fluid but do not put the cap on the reservoir. Press the clutch pedal several times to expel any air pockets from the hydraulic lines and top off the reservoir with more fluid. After you have bled the lines, replace the cap and tighten it.

    8

    Reconnect the battery to complete the repair process.

Read here..