Showing posts with label rusty. Show all posts
Showing posts with label rusty. Show all posts

Sunday, March 2, 2014

How to Repair a Rusty Car Panel

How to Repair a Rusty Car Panel

Over a period of time, car panels will start to rust. Although rust is generally easy to treat, it can damage a cars look and sale value if not treated properly and quickly. It is best to treat the problem as soon as you notice the rust; failure to deal with it quickly will see the problem increase and become a lot harder to deal with.

Instructions

    1

    Locate the area on the car panel affected with rust. Use the sandpaper and white spirit to remove the rust by rubbing it. White spirit is a cleaning liquid solvent primarily used to remove stains, rust and dirt from objects such as cars and brick.

    2

    Use the wire brush to scrape away any rust still on the panel.

    3

    Put some rust solvent on another piece of sandpaper and gently wipe the area where the rust was. This will get rid of any micro bits of rust left.

    4

    Put tape around the area where the rust was and then spread an even amount of epoxy body filler over the area. Allow it to dry for a few hours. The filler will cover any scratches or small holes that the rust caused and the tape will protect your car from paint. Sand to smooth surface.

    5

    Cover the area of the panel with primer. When dry, paint the area of the car panel which was affected with a paint matching the car, using the tape as a boundary. Allow the first coat to dry and then apply a second.

    6

    After the second coat is dry, polish and wax the area to finish off your repaired car panel.

Read here..

Thursday, November 14, 2013

How to Remove Exhaust Flange Bolts That Are Rusty

The constant heating and cooling of your vehicles exhaust system, combined with moisture, will quickly cause the exhaust flange bolts to rust and seize. The rust has often progressed to the point that the threads of the exhaust flange bolts are unusable. To release the exhaust flange bolts, you will need to apply heat to remove the rust from the threads; and if the threads are beyond use, you will need to cut the bolts from the exhaust flange.

Instructions

    1

    Inspect the area around the exhaust flange bolts to make sure that there are no fuel lines or combustible materials within the area and clear any combustibles from the area underneath the vehicle.

    2

    Put on your leather work gloves and tinted safety glasses.

    3

    Place the fire extinguisher close to you in an unobstructed area so you can easily reach the extinguisher in case there is a fire.

    4

    Turn on the acetylene and ignite the torch with the striker. Turn on the oxygen and set the flame hot by increasing the oxygen until the inner bright blue flame is about 1/2 of an inch long.

    5

    Set the tip of the torch 6 to 8 inches away from the first exhaust flange bolt and heat the bolt until it has a dull orange glow then turn off the oxy-acetylene torch. Do not use the air trigger to heat the bolt faster.

    6

    Allow the exhaust flange bolt to cool and then place a socket that fits the bolt head onto the ratchet.

    7

    Slide the socket onto the nut located on the exhaust flange bolt and turn the ratchet handle counterclockwise to loosen the exhaust flange bolt. If the first nut will not loosen, proceed to the next step. If the bolt loosens, repeat the process with the rest of the exhaust flange bolts.

    8

    Reignite the oxy-acetylene torch, set the flame as described in Step 4 and place the tip of the torch 3 to 4 inches away from the head of the exhaust flange bolt.

    9

    Heat the bolt head until you see a bright orange glow emitting from the metal and then hit the air trigger to blow additional oxygen onto the bolt. You will see the bolt head melting and blowing toward the floor.

    10

    Turn off the oxy-acetylene torch and immediately strike the threaded side of the exhaust flange bolt with a hammer to remove the bolt from the exhaust flange. Repeat the procedure with each exhaust flange bolt to free the exhaust flange from the manifold.

    11

    Allow the bolts and molten metal to cool for at least 30 minutes before you leave the area to ensure that no combustible materials catch on fire.

    12

    Clean up and dispose of the cut exhaust flange bolts after they have cooled for one or two hours to reduce the chances of starting a fire in a garbage can.

Read here..