Sunday, January 26, 2014
How to Put Bolts in a Side Post Battery
The side post battery is a simple connection that has a special bolt with a large built-in flat washer surrounded by and tucked under a plastic cover. This terminal, bolts to a flat lead post with a 3/8-inch threaded hole in the center. The plastic cover of the side post terminal holds the special bolt securely in place and protects the connections from the elements reducing corrosion which reduces connection failures. If the terminal bolts head or threads become stripped or damaged the bolt should be replaced. Replacement bolts are available.
Instructions
- 1
Disconnect both side post terminals from the battery using a socket and ratchet or vise grip pliers if the bolts head is stripped. Remove the negative terminal of the battery first.
2Thread a 3/8-inch nut a few turns onto the terminal bolt to be removed. The nut will expand the surface area of the bolt end.
3Pull the terminal with the bolt to be removed away from the battery. Select a deep well socket that is much larger than the terminal bolts washer located under the plastic cover and place it centered over the head of the bolt.
4Hammer the nut end of the terminal bolt while supporting the other side with a large deep well socket until the bolt pushes through the plastic and into the socket. It may require the socket be backed up against the engine block or a solid surface.
5Place the new terminal bolt into the terminal and use a small screwdriver like a shoe horn to slip the washer ledge of the new bolt under the plastic cover.
6Brush the battery posts clean with a wire brush.
7Reconnect both battery terminals. Connect the positive terminal first as a safety precaution.
Thursday, November 14, 2013
How to Remove Exhaust Flange Bolts That Are Rusty
The constant heating and cooling of your vehicles exhaust system, combined with moisture, will quickly cause the exhaust flange bolts to rust and seize. The rust has often progressed to the point that the threads of the exhaust flange bolts are unusable. To release the exhaust flange bolts, you will need to apply heat to remove the rust from the threads; and if the threads are beyond use, you will need to cut the bolts from the exhaust flange.
Instructions
- 1
Inspect the area around the exhaust flange bolts to make sure that there are no fuel lines or combustible materials within the area and clear any combustibles from the area underneath the vehicle.
2Put on your leather work gloves and tinted safety glasses.
3Place the fire extinguisher close to you in an unobstructed area so you can easily reach the extinguisher in case there is a fire.
4Turn on the acetylene and ignite the torch with the striker. Turn on the oxygen and set the flame hot by increasing the oxygen until the inner bright blue flame is about 1/2 of an inch long.
5Set the tip of the torch 6 to 8 inches away from the first exhaust flange bolt and heat the bolt until it has a dull orange glow then turn off the oxy-acetylene torch. Do not use the air trigger to heat the bolt faster.
6Allow the exhaust flange bolt to cool and then place a socket that fits the bolt head onto the ratchet.
7Slide the socket onto the nut located on the exhaust flange bolt and turn the ratchet handle counterclockwise to loosen the exhaust flange bolt. If the first nut will not loosen, proceed to the next step. If the bolt loosens, repeat the process with the rest of the exhaust flange bolts.
8Reignite the oxy-acetylene torch, set the flame as described in Step 4 and place the tip of the torch 3 to 4 inches away from the head of the exhaust flange bolt.
9Heat the bolt head until you see a bright orange glow emitting from the metal and then hit the air trigger to blow additional oxygen onto the bolt. You will see the bolt head melting and blowing toward the floor.
10Turn off the oxy-acetylene torch and immediately strike the threaded side of the exhaust flange bolt with a hammer to remove the bolt from the exhaust flange. Repeat the procedure with each exhaust flange bolt to free the exhaust flange from the manifold.
11Allow the bolts and molten metal to cool for at least 30 minutes before you leave the area to ensure that no combustible materials catch on fire.
12Clean up and dispose of the cut exhaust flange bolts after they have cooled for one or two hours to reduce the chances of starting a fire in a garbage can.
Sunday, November 10, 2013
How to Loosen Rusted Nuts Bolts on Mufflers
Rusting bolts are a pain to deal with but can be loosened with special equipment. When it comes time to dealing with a set of rusting nuts and bolts on your muffler, that can be tricky as well, as sometimes it can be more difficult to access the hardware. Fortunately, with a few tricks, it can be done.
Instructions
- 1
Lift the vehicle in the air using the jack and secure it on jack stands. Make sure the vehicle is secure before you crawl underneath it.
2Locate the rusted hardware on the muffler you wish to remove. Spray the penetrating lubricant onto the bolt and nut, coating it thoroughly. Clean up excess lubricant with a shop rag.
3Loosen the bolt using the 3/8-inch ratchet and socket set. You may be able to break the bolt free from the rust with just one application of the penetrating lubricant.
4Apply more penetrating lubricant to the rusted bolt if needed. Coat all surfaces and down into the threads if possible. Allow this to sit overnight.
5Attempt to remove the bolt again using the 3/8-inch ratchet. Repeat Step 4 until the bolt can be removed.