Fix It

The outside door handle on the drivers side of the car may be removed because it is being replaced, repaired, or the car door itself is undergoing repair. Most amateur mechanics may find that removing a car door handle is easy, but it can be difficult to remember how to reinstall one. Reinstalling the outside drivers side door handle shouldnt take more than a half hour if the door panel has already been taken off on the inside. With a few simple connections the door handle can be secured to the door and used.

Instructions

1

Remove the door panel as necessary. Because you are reinstalling the door handle the panel is probably already off from the inside of the door. If the panel is not off, take a screwdriver and pop the panel out of place.

2

Slip the plastic retaining clip at the end of the rod onto the door handle. Slide the door handle onto the rods in the door so that one connects to the door latch and one connects to the lock.

3

Press the door handle into place on the drivers side door.

4

Secure the door handle in place with nuts and a socket wrench. Tighten the nuts so that the handle is firmly in place.

5

Shut the door and open it to make sure the door handle has been correctly installed and works.

6

Reassemble the inside of the door. Snap or screw the door panel back into place with a screwdriver or the included plastic clips. Replace any speakers, window leavers, or handles.

Chrysler reintroduced the 300 lineup in 1999, with the unveiling of the 300M model. In 2005, Chrysler dropped the "M" from the 300 and completely redesigned this four-door sedan. The 2006 Chrysler 300C came standard with a 5.7-liter Hemi V-8 engine that cranked out 340 horsepower. The 300C also came standard with the HomeLink system that could be programmed to open a garage door and even turn on the lights in a home without the owner having to get out of the car. This system, however, does not program automatically. You must follow a programming process for this system to work on your house.

Instructions

Single Code Garage Door Opener

1

Park your 300C near your garage door. Press and hold the two outer buttons on the HomeLink system -- the garage door buttons -- for 20 seconds and observe as "Channels Cleared" appears in the Electronic Vehicle Information Center, located between the speedometer and tachometer.

2

Hold your garage door transmitter about three inches away from the HomeLink buttons. Press and hold the garage door opener button and the HomeLink button you intend to use for the garage door, at the same time.

3

Release the buttons when the EVIC displays "Channel X Trained" -- the "X" indicates the HomeLink button that you programmed.

4

Hold the button you just programmed and check the EVIC display. If it reads "Channel X Trained," with "X" being the HomeLink button number, then you programmed the system correctly. If the EVIC displays "Did Not Train," repeat steps 2 and 3.

5

Repeat steps 2 through 4 to program the remaining two buttons, if needed. Do not repeat Step 1, as this deletes all programs.

Rolling Code Garage Door Opener

6

Follow steps 1 through 5 in the section titled "Single Code Garage Door Opener."

7

Locate the "Learn" or "Smart" button on the garage door opener motor. The exact positioning varies on every model opener, but its typically found near the antenna. Press and release the "Learn" or "Smart" button.

8

Hold the programmed HomeLink button for two seconds and release it. Repeat this step two or three times -- the exact number of times depends on the brand of garage door opener.

Removing the pins from the door hinges of your Mustang will allow you to remove the door or replace worn bushings on the hinges. When you remove the pins, the door will be unattached and must be supported or it will fall, potentially damaging the door, window, or other components. New pins and bushings are sold at auto parts stores.

Instructions

1

Open the door of your Mustang and slide a jack under the door. Place a piece of wood between the bottom of the door and the jack, and raise the wood with the jack until the door is resting on the wood.

2

Locate the top pin in the center of the door hinge and tap the bottom of the pin with a hammer to push it up. Do not drive the pin out of the hinge; just push it high enough to create a gap between the top of the hinge and the head of the pin.

3

Slide a flat pry bar under the head of the pin and pry it up and out of the hinge as you stabilize the door to keep it from falling over. Move the bar to the bottom pin and pry it out.

4

Lift the door off the hinges and set it aside.