Showing posts with label bmw. Show all posts
Showing posts with label bmw. Show all posts

Wednesday, April 9, 2014

How to Replace Struts on a 2003 BMW 330

The 2003 BMW 330 is a rear wheel drive sedan that uses independent suspension setups on all four wheels. The independent suspension relies on struts to absorb bumps in the road. However, these struts wear out like any other automotive components, and the stock OEM struts need to be replaced every 60,000 miles. Replacing the struts yourself can save you a lot of money and should only take a day for most people to do.

Instructions

    1

    Park the 2003 BMW 330 somewhere flat with a lot of room to the sides. Also make sure that you are not blocking anyone in as the car will be stuck in place until the struts are all changed out. Put it in "Park" and then turn the sedan off. Jack up the car by sliding a car jack under the jack points at each corner. When a corner is elevated, slide in a jack stand to keep the car up. Once the car is fully elevated, remove the wheels from the 330 with your tire iron.

    2

    Unbolt the sway bar linkages from both the front and the rear wheels. The sway bars help keep the car from wallowing in the corners by connecting opposite side control arms. The bars are held to the bottom of the car by bushing mounts, but all you need to do is unbolt the ends of the bars from the bottom control arms. Rotate the ends of the sway bars down so that they are out of the way.

    3

    Unbolt the single bottom retaining bolt on the front right strut. Use a breaker bar to wedge the bolt out as it will be firmly stuck in. Then unbolt the top three bolts at the top of the strut and use the breaker bar to wedge the entire strut out. Be caul to support the strut so that it does not fall. Then bolt in the top of the new strut into the 330s frame. Once it is supported, raise the steering knuckle up and bolt in the bottom of the strut. Repeat this process on the left front wheel as well.

    4

    Fold down the rear seat of the 300 and pull off the plastic tab over the top of the struts. Unbolt the bolt underneath for the right rear, and then go to the right rear wheel well and unbolt the bottom of the bolt from the hub assembly. Pry the strut out with the breaker bar and place it to the side. Bolt in the new strut and then repeat the process on the left side. Replace the plastic tabs and then fold the back seat back up.

    5

    Bolt the sway bars back into place and then put the wheels back on the 330. Lower the 330 off the stands and then look at the corners to make sure the struts are supporting the cars weight.

Read here..

Saturday, February 15, 2014

How to Reset a BMW E36 SRS Light

How to Reset a BMW E36 SRS Light

In order to remove and reset the air bag light, also known as the SRS light on a BMW, a reset tool is needed. The Service Light Plus airbag reset tool, which is available for purchase at most auto parts stores, is designed to work on the BMW E36 and is easy to use by connecting it to the BMWs data link connector, located under the vehicles dashboard beside the hood release latch.

Instructions

    1

    Park the BMW on level ground.

    2

    Attach the air bag reset tool to the BMWs data link connector, under the dashboard.

    3

    Switch the BMWs ignition on.

    4

    Anticipate for the tools screen to illuminate and select "BMW" on the screen with the scroll buttons on the tool and press the reset tools "OK" button.

    5

    Use the scroll buttons to select the "E36" model and press the "OK" button.

    6

    Use the scroll buttons to select "Reset of Airbag" and press the "OK" button.

    7

    Wait for the message "Reset OK." Switch the BMWs ignition off and remove the air bag reset tool.

Read here..

Wednesday, October 30, 2013

How to Reset the Maintenance Reminder Light for a 1987 BMW 325is

How to Reset the Maintenance Reminder Light for a 1987 BMW 325is

The 1987 BMW 325is has a built-in maintenance reminder light to let you know when you need to take your BMW in to see the mechanic for regular servicing. If the "Service Engine" light illuminates on the instrument panel in yellow or red when you start the engine, then it is time for a servicing. Make sure you have the servicing done before you attempt to reset the light or else it will turn itself back on. The reset requires the help of a reset tool purchased from an auto parts store.

Instructions

    1

    Put the key into the ignition and turn the vehicle to the "On" position, but dont allow the engine to turn over.

    2

    Turn off all accessories such as the lights, air conditioner, and the radio.

    3

    Pop up the hood of the BMW and locate the diagnostic connector on the front left side of the engine as you are facing the vehicle. Plug the BWM reset tool into the diagnostic connector.

    4

    Find the "Service Engine" button on the BMW reset tool and push and hold it for ten seconds or until the light on the tool flashes and then turns off. Release the button and unplug the reset tool from the diagnostic connector. Lower the hood.

    5

    Look on the instrument cluster inside the vehicle to see that the "Service Engine" light has turned off.

Read here..