Showing posts with label 2005. Show all posts
Showing posts with label 2005. Show all posts

Tuesday, December 24, 2013

How to Replace the Taillight Cover on a 2005 Ford F 150 Lariat

Replacing the taillight cover or lens on your 2005 Ford F-150 truck requires replacing the entire taillight assembly. The assembly and lens are molded together and cannot be separated. Replacement taillight assemblies are available from Ford, most auto parts stores, salvage yards and some specialty parts retailers. Replacement of the assembly takes about 10 minutes with the use of basic tools. Check the bulbs while you have the taillight covers off, and replace any bulbs that are not working.

Instructions

    1

    Open the tailgate of your 2005 F-150, allowing the tailgate to rest on the support cables. Locate the two retaining screws in the bedside where the tailgate closes. The retaining screws are threaded into the taillight assembly.

    2

    Remove the two screws with a Phillips screwdriver and set them aside. Grasp the taillight assembly from the rear and pull it straight back, removing it from the truck. Do not pull it out so far that you damage the wires behind it.

    3

    Locate the bulb sockets on the rear of the assembly. Turn the bulb sockets counterclockwise, and remove them from the assembly. Discard the old assembly.

    4

    Install the bulb sockets in the rear of the new taillight assembly, turning them clockwise to lock them into place. Slide the new assembly into place on the truck. Push the assembly in until is seats completely.

    5

    Install the two retaining screws, and tighten them with a Phillips screwdriver. Do not tighten the screws so much that they thread into plastic, which could crack the housing. Close the tailgate.

Read here..

Friday, December 6, 2013

How to Change the Light Bulb in a 2005 Honda Accord

How to Change the Light Bulb in a 2005 Honda Accord

The 2005 Honda Accord uses different light bulbs in each headlight assembly for the low beams and high beams. Changing a low beam bulb involves a different procedure than the high beam bulb. To ensure the correct bulb is being replaced, its best to locate the faulty bulb before purchasing and replacing it in order to obtain the correct part. The bulbs look the same but are intended for different uses. The low beam bulbs are on the outer edge of the headlight assembly, and the high beam bulbs are on the inner edge.

Instructions

Low Beams

    1

    Start the engine and turn the steering wheel in the opposite direction of the headlight being replaced. Turn it all the way to the right if replacing the drivers side low beam or all the way to the left if replacing the passengers side low beam. Turn the engine off and ensure the headlight switch is in the "Off" position.

    2

    Remove the two retaining clips holding the inner fender splash cover with a flat head screwdriver. Pop the center pin of the retaining clip upward then pull the clip assembly out of the fender splash cover.

    3

    Pull the fender splash cover away from the fender and bumper with one hand and reach in with the other hand to grasp the socket of the low beam headlight bulb.

    4

    Disconnect the wire harness plug from the headlight bulb by squeezing in on the sides to unlock it then pull it off the socket of the low beam headlight bulb.

    5

    Rotate the bulb socket a 1/4 turn counterclockwise to align its retaining tabs to the release grooves of the headlight assembly then remove the bulb.

    6

    Hold the replacement 9006 low beam headlight bulb by its socket to avoid touching the glass bulb. Oils and perspiration in skin will damage the bulb.

    7

    Align the retaining tabs of the bulb socket to the release grooves in the headlight assembly. Push slightly inward and rotate the socket a 1/4 turn clockwise to lock it in place. Reconnect the wire harness plug and test the headlight before replacing the retaining tabs of the fender splash cover.

High Beams

    8

    Open the hood and remove the two retaining clips from the air intake cover on the passengers side high beam with the screwdriver as noted in Step 3. For the drivers side high beam replacement, proceed to Step 2.

    9

    Detach the wire harness connection from the high beam bulb by squeezing the sides to unlock it then pulling it out of the bulb socket.

    10

    Rotate the socket of the headlight bulb a 1/4 turn counterclockwise to remove it from the headlight assembly.

    11

    Install the replacement 9006 headlight bulb (again, do not touch the glass bulb section) by reversing the removal procedure.

    12

    Reconnect the wire harness plug to the headlight bulb socket and test the headlight before replacing the air intake cover and retaining clips for the passengers side.

Read here..

Friday, November 29, 2013

How to Replace Injectors on a 2005 F 350

The Ford F series is a group of full-size pickups manufactured by Ford Motor Company. The model number indicates the nominal carrying capacity of the vehicle, such that an F350 is a 3/4-ton pickup truck. A 2005 F350 typically has a 6.0-liter turbo diesel engine with fuel injection. The fuel injectors deliver a precise ratio of fuel and air to the engine in a specific sequence. The replacement of the fuel injectors in an F350 will also require you to remove additional components.

Instructions

    1

    Remove the valve cover for the fuel injectors with a socket wrench and detach the electrical connector for the fuel injector. Disconnect the mounting bolts for the crankcase-to-head tube assembly and remove the assembly. Remove the mounting bolts for the oil rail and disconnect the oil rail.

    2

    Push the electrical connector for the fuel injector out of the rocker arm carrier with a small pry tool. Plug the holes for the oil drain that are next to the each glow plug with clean shop towels. Remove the mounting bolt for the fuel injector with a socket wrench and release the hold down clamp for the fuel injector. Disconnect the fuel injector and unplug the oil drain holes.

    3

    Install new O-rings and washers onto the new fuel injector and apply a liberal coat of clean engine oil to the fuel injector. Install the fuel injector and attach the hold-down clamp for the fuel injector. Torque the mounting bolt for the fuel injector to 24 foot-pounds with a torque wrench.

    4

    Place the electrical connector for the fuel injector into the rocker arm carrier with the pry tool. Lubricate the O-rings on the top of the fuel injector with clean engine oil.

    5

    Place the oil rail into position onto the fuel injectors and press down on the oil rail to secure it in place. Torque the mounting bolts for the oil rail to 10 foot-pounds with a torque wrench.

    6

    Attach the crankcase-to-head tube assembly to the engine and torque the mounting bolts to 60 foot-pounds with a torque wrench. Connect the electrical connector for the fuel injector and install the valve covers with a socket wrench.

Read here..