Monday, November 4, 2013
How to Remove a Fairing 2000 Ultra
Properly speaking, there are two fairings on the front of a 2000 FLHTCU. The big batwing that protects you from the wind when you get in the wind is the outer fairing. It, with the windshield, attaches to the rest of the chassis with a total of seven screws. Once it comes off the inner fairing remains. The inner fairing holds the instruments, radio, stereo speakers and other amenities Harley sells with Electra Glides. It is also easily removed by unfastening just four screws. There are a few steps before a rider can reach those last four screws, however.
Instructions
- 1
Drape a folded blanket over the front fender and wheel to protect the finish.
2Loosen and remove the three Torx screws just below the windshield in front of the fairing and the two screws just outside and below the speakers inside the fairing with a Torx head driver.
3Expose the two outer fairing screws just below the fairing cap on the right and left side by turning the handlebars all the way to the left and all the way to the right. Loosen and remove both of them with a Torx head driver.
4Remove the wire connector at the back of the headlamp assembly by simultaneously squeezing both sides of the connector with your fingers and pulling. Straddle the front of the bike and lift the fairing off with both hands to expose all the wiring harness connections beneath. Lift the loose windshield off the front of the motorcycle.
5Pull the turn signal connectors apart into halves. Pull the passing light connector apart into halves.
6Unfasten the passing light bracket from the forks with a Torx head driver and remove the passing light assembly.
7Turn the ignition key left to "unlock." Turn the cam shaped ignition knob right to "access."
8Slide a small screwdriver under the ignition knob and push up the release button under the left side of the knob. Push the key down, turn the knob left and lift the knob off the rest of the ignition switch to expose the switch post and switch nut.
9Loosen the switch nut with a small combination wrench and pull the nut, spacer and collar off the switch post. Pull the broad chrome skirt on the bottom of the inner fairing up and off.
10Loosen the clutch cable adjuster nut and the clutch cable adjuster lock nut on the clutch cable near the left down tube with two combination wrenches. Completely slacken the clutch cable.
11Remove the clutch control pivot pin and retaining ring with a flathead screwdriver. Loosen the clutch lever bracket with a Torx head driver and remove the clutch lever from the bracket.
12Disconnect the clutch cable from the end of the clutch lever. Feed the clutch cable through the weatherproof grommet in the bottom middle of the inner fairing.
13Cut a small square from a typical, 1/8 inch thick cardboard, produce box and insert the square between the front brake lever and the brake lever housing to protect the stop signal plunger from damage. Remove the switch housing and master cylinder from the right side of the handlebars with a Torx head driver.
14Pull the throttle off the right end of the handlebars using a flathead screwdriver. Disconnect the idle and throttle cables wrapped around the inside end of the throttle.
15Feed the idle and throttle cables through the weatherproof grommet in the bottom middle of the inner fairing.
16Disconnect the cigarette lighter from the exposed wiring harness. Loosen and remove the six speaker adapter screws with a Torx head driver. Remove the speaker adapters.
17Disconnect the fuel gauge and voltmeter from the exposed wiring harness. Loosen the four screws that hold the inner fairing to the fairing bracket with a Torx head driver.
18Pull the bottom of the inner fairing and slide it off the mounting pegs. Pull the bottom of the fairing mounting bracket to free it from the mounting pegs.
19Pull the inner fairing from the mounting bracket and remove the inner fairing.
Saturday, November 2, 2013
My 2002 Harley Davidson Ultra Classic Wont Start
Before you can start your 2002 Harley-Davidson Ultra Classic you must have gasoline in your gas tank, the petcock must open, the ignition switch must be turned on and the engine run switch must be turned on. Your enrichener or choke should be fully open and your hand should be off the throttle. If the solenoid chatters when your try to start the bike, your battery is dead or your battery cables are corroded. Most other reasons why the motorcycle will not start can be evaluated or remedied by taking the following steps.
Instructions
- 1
Examine the spark plug wires and the connections between the plug wires, the spark plugs and the coil. If the plug wires are cracked, frayed or visibly corroded they must be replaced. If any connection is loose push it back together with your fingers.
2Remove the front and back spark plugs with a socket wrench and a spark plug socket. Remove each spark plug by turning it counterclockwise and look for visible signs of fouling. The electrodes should be light tan or gray and intact. Replace if fouled.
3Remove the plug wire leads from the coil electrodes. Look for corrosion on the coil electrodes. Remove any corrosion with a wire brush.
4Remove the seat bolt from the back of your seat. Pull the seat back off to access the battery. Your battery is dead if the solenoid chatters when you try to start the bike. If the battery is dead, then connect the positive and negative leads from a motorcycle battery charger to the same terminals on your battery.
5Charge the battery for four hours. Attempt to restart the Ultra Classic.
6Examine the battery terminals and cables for signs of corrosion. Remove any corrosion with a wire brush. Replace the battery if it will not charge or if a terminal is broken.
7Troubleshoot your carburetor. Remove the air cleaner cover by unscrewing the Allen bolt or bolts securing it to the air cleaner.
8Loosen the air cleaner by removing the three or four Torx bolts that secure the air cleaner to the backing plate. Hold the air cleaner in your less dominant hand while you disconnect the breather tubes from the top of the air cleaner with a box wrench.
9Remove the air cleaner backing plate. Examine both throttle cables. Ensure they are both attached to the throttle cam.
10Access the fuel air adjustment screw on the bottom of the carburetor. Gently turn the adjustment screw clockwise with a small, flat-head screwdriver until it is fully closed. Turn the adjustment screw counterclockwise 2-1/8 turns. Attempt to start the motorcycle again.